Denali d4 led auxiliary headlight kit with dialdim-universal controller for motorcycle spare parts moped accessories

€876.17
Tax included
Denali D4 LED auxiliary headlight kit with dialdim-universal controller for motorcycle spare parts moped accessories
Quantity
Out of stock

  • Buy and pay securely with our SSL gateway using Visa, Mastercard and/or Paypal Buy and pay securely with our SSL gateway using Visa, Mastercard and/or Paypal
  • Shipments in less than 48 hours by urgent and insured agencies. Shipments in less than 48 hours by urgent and insured agencies.
  • Up to 30 days for returns, contact us to resolve any issues. Up to 30 days for returns, contact us to resolve any issues.
PayPal

DENALI D4 LED auxiliary headlight kit with DialDim™ controller - Universal.

Kit consists of:

  • (x2) - Headlight DENALI D4 DataDim™ LED auxiliary
  • (x1) - DENALI DialDim™ lighting controller

Component description:

1 - DENALI D4 DATADIM™ LED AUXILIARY HEADLIGHT

Simply put; The DENALI D4 is a beast. It is DENALI's most powerful light with an output of 4380 lumens in an aggressively styled housing. The installed hybrid lens is Equipped with two elliptical flood lenses and two spot beam lenses to create the ultimate hybrid beam pattern; a super wide close range flood and penetrating spot beam in a housing. The included spot lens throws out a huge beam of light and has an official E-Mark certification.

D4 Capsule Features

< ul>High-intensity series Cree LEDs with 4380 lumen output per capsuleDrySeal™ can withstand the most extreme environmentsLiveActive™ Thermal Management keeps LEDs cool by preventing loss of light output due to overheatingLow profile mounting bracket with stainless steel hardware includedIncludes flood lens. Additional E-Mark approvedAmber lenses available (sold separately) DNL.D4.10100

D4 Sheath Specifications< /strong>

  • LED: (4x) 10 watts Cree XPL HI
  • Power consumption: 3.3 amps Gross Lumens
  • mens : 4380
  • DataDim™ Compatible: Yes
  • Operating Voltage: 12 VDC
  • Pod Size: 3.9 square x 2.6 deep Weight< /li>
  • sheath: 1.55 pounds
  • IP67 waterproof and submersible
  • E-brand approved spot lens

D4 Pod - What What's in the box?

  • (1x) LED light capsules
  • (1x) True-Hybrid™ (installed)
  • (1x) E-Mark approved spot lenses (included)
  • (1x) Hinge brackets with M8 stainless steel hardware
  • ( 1x) Wiring pigtail

2 - DENALI DIALDIM™ LIGHTING CONTROLLER

Our innovative DialDim™ Features a multi-color halo dimmer switch that allows you to independently turn on/off and dim two sets of 3-wire auxiliary lights from a single consolidated wiring harness. The LED halo switch shows your exact settings and allows for effortless dimming on the fly. The blue halo controls light set one and the green halo controls light set two; Simply double-click to switch between the two circuits.

The controller also features high beam, turn signal and horn inputs to unlock smart flash functions that can override your auxiliary lights with your turn signal, turn on your auxiliary lights as a turn signal, or turn on your lights when your horn sounds.

More features, more feedback!< /strong>

Our patent-pending multi-color halo dimmer switch can do much more than just turn your lights on and off and dim them. For starters, it shows the exact intensity of both lights so you never have to guess if the lights are on or in what state. intensity are set.

With electronically fused circuits, the halo switch can also display and allow you to select fuse values for each circuit. And if a fuse blows, the LED halo will turn dark. Red will provide real-time feedback and will allow reset the fuse.

Last but not least, the halo switch also functions as a battery monitor with a low voltage cut-off function. Our industry-first design will flash brightly. It will turn on in different colors when turned on to show the battery status and will turn off. Automatically turns on auxiliary lights if the battery voltage drops below 10.8 volts.

Both the controller housing and switch feature a fully waterproof design with gaskets and O-rings at each joint to ensure trouble-free operation in outdoor environments.

Features

  • < li>
ON/OFF and Dimming - Independently control the on/off of two sets of lights and the intensity level with the single DialDim™ switch. The blue halo controls light set one and the green halo controls light set two. Double click to switch between the two circuits.High/Low Sync- Your auxiliary lights will automatically switch between the dim setting selected and maximum intensity with the factory high beam switch. Simply connect the blue input wire to your vehicle's high beam circuit to enable this feature.Stealth Mode - A smart setup The 0% dimming setting on the switch allows the lights to be off during normal driving conditions, but will increase to 100% intensity with your vehicle's high beam switch. The lights will also react to turn signal and horn inputs in this mode, but will remain off when no inputs are detected. Cancel with signal of turning - When it is When enabled, the headlights (blue circuit 1) will be canceled in sync with your signal to avoid washing your factory turn signal. Simply connect the yellow and orange input wires to your vehicle's turn signal circuit to enable this feature.Flash as turn signal  - When it is When enabled, the amber visibility lights (green circuit 2) will flash in sync with the factory turn signals. Simply connect the yellow and orange input wires to your vehicle's turn signal circuit to enable this feature.Strobe Light with Horn  ;- When it is When enabled, the auxiliary lights on both circuits will flash at 4Hz when the horn sounds. Simply connect the green input wire to your vehicle's horn circuit to enable this feature.Electronically Fused Circuits - ¡ Both light circuits are electronically fused and can be configured directly from the switch itself! The halo will light up It will turn red to notify you when a fused circuit is tripped.Voltage display indicator- When starting the vehicle, the switch halo will flash. ; It is green to indicate that the battery voltage is low. is in good condition or will flash It turns red to indicate that the battery voltage is low. below 11.8V.Low Voltage Cut-Off - If the battery voltage drops below 10.8V, the lights They will not turn on, which will prevent let him be stranded. The switch halo will flash. 4 red LEDs to indicate low voltage condition.

*To enable functions related to high beam, turn signal and horn, you must connect to a clean 12v circuit in your vehicle. To disable these features, simply do not connect to the corresponding vehicle circuit.

Product Specifications

  • Two light circuits completely independent.
  • Eight intensity levels per circuit (5%, 15%, 30%, 45%, 60%, 75%, 100%)
  • Eight values of electronic fuses. Single (1A, 2A, 4A, 6A, 8A, 10A, 15A, 20A)
  • Five feature input wires (power, high beam, horn, left turn, right turn )
  • 20 A max. per circuit (30 Amps max combined)
  • Operating Voltage: 12 VDC

What? What's in the box?

  • (1x) DialDim™ controller harness
  • (1x) DialDim™ multifunction switch< li>(1x) 7/8 Handlebar Switch Mount
  • (4x) 66' Plug-&-Play Light Extensions
  • (1x) Wire Harness Universal input trigger

Light type LED
Packaging per 3
Color Black
Width (mm) 99mm
Length (mm) 65mm
Homologation Not approved in Switzerland
Front Position
Aluminum Composition
DENALI
VM3064445

Reviews

No customer reviews for the moment.

Write your review

Denali d4 led auxiliary headlight kit with dialdim-universal controller for motorcycle spare parts moped accessories

Denali D4 LED auxiliary headlight kit with dialdim-universal controller for motorcycle spare parts moped accessories

Write your review